OpenPCD usbserial problem

[Martin]

Hello,

I bought a OpenPCD a few days ago. I have Debian Etch installed with
Kernel 2.6.18-5-686.

First I have successfully compiled dfu-programmer-0.3.0-hmw4,
librfid-0.1.0 & sam7utils-0.1.0-bm.
I have plugged in OpenPCD with "Bootloader button" pressed. Then I have
started dfu_programmer as root like this:

*./dfu-programmer openpcd dfu_dnload
/path/to/openpcd/firmware/main_dumbreader.bin*

Then this output comes:

/looking for 16c0:076b
determining device status: state = 0, status = 0
Device in Runtime Mode, send DFU detach request...
Resetting USB...
error resetting after detach: could not reset: No such device
looking for 16c0:076b
dfu-programmer: no device present.

/Because I´ve read this mailinglist for a while, I´ve tried a

*rmmod usbserial*
&
*modprobe usbserial vendor=0x16c0 product=0x076b*
and got this output:
/
looking for 16c0:076b
determining device status: state = 2, status = 0
dfuIDLE, continuing
wTransferSize = 0x0100
Starting download:
[#########################################################################################################]
finished!
Resetting USB...
error resetting after download: could not reset: No such device
dfu-programmer: failed to release interface 0.

/Then I have tried a/

/*./librfid-tool --scan-loop

*and got this output:*
*/
lt-librfid-tool - (C) 2006 by Harald Welte
This program is Free Software and has ABSOLUTELY NO WARRANTY

initializing librfid
opening reader handle
No Omnikey Cardman 5121 found
No OpenPCD found either

/Ok, I think the FW is installed (!?) but I think there are some
problems with connection, so I typed "*lsusb*" and there is this output:

/Bus 005 Device 003: ID 0846:6a00 NetGear, Inc. WG111 WiFi (v2)
Bus 005 Device 001: ID 0000:0000
Bus 002 Device 003: ID 046d:c517 Logitech, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 003 Device 009: ID 16c0:076b
Bus 003 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

/"/dev/ttyUSB0" is there, but when plugging out and then again plugging
in, there is a strange error output, here:/

usb 3-1: USB disconnect, address 8
usb 3-1: new full speed USB device using uhci_hcd and address 9
usb 3-1: configuration #1 chosen from 1 choice
usbserial_generic 3-1:1.0: generic converter detected
usb 3-1: generic converter now attached to ttyUSB0
usbserial_generic 3-1:1.1: generic converter detected
usbserial_generic 3-1:1.1: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 3-1:1.1 failed with error -5
usbserial_generic 3-1:1.2: generic converter detected
usbserial_generic 3-1:1.2: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 3-1:1.2 failed with error -5


/I have tried the whole thing at another computer with Debian Etch and
wih a GRML 1.0 Live CD and with a Knoppix STD Live CD.
The usbserial problem was always the same as above!!!


What can I do now?
Have I done something wrong?
Can anyone help me, please?


Regards

Martin F.