Question about OpenPCD firmware

Wed Jan 23 02:08:42 UTC 2008

I've purchased two OpenPCD sets - and they look nice. And as per what I normally
do I followed the instructions to update the firmware on one of the devices
(leaving the other device in pristine state).

The journey through updating the firmware was an interesting one. After redoing
  the firmware in the one which wasn't responding using the 262 version off the
website which is certainly different to the version in SVN - the green light
doesn't blink for instance - so obviously that wasn't the firmware loaded when
the devices were shipped to me (in mid December).

And I can use opcd_test to change led settings and to get the serial number, but
librfid isn't working to grab card details. I compiled it up with debug so I
could get some useful output. There are strange things in the output.

Hopefully the three different debug outputs will help someone figure out what
steps I can take to get the device back to "factory state" - or determine if I
actually have a non-working device.

If I've sent this email to the wrong place then please redirect me to the right
location.

Thanks,
Tim.

---8<---

NON-WORKING-262-FIRMWARE

lt-librfid-tool - (C) 2006 by Harald Welte
This program is Free Software and has ABSOLUTELY NO WARRANTY

initializing librfid
opening reader handle
No Omnikey Cardman 5121 found
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=11: OK
rfid_asic_rc632.c(158):rc632_power_up: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=11: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x00, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_asic_rc632.c(151):rc632_turn_off_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=58: OK
rfid_asic_rc632.c(144):rc632_turn_on_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, val=58: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(500):openpcd_open: returning 0xb7fdde3c
scanning for RFID token...
rfid_scan.c(54):rfid_layer2_scan: testing l2 0
rfid_scan.c(54):rfid_layer2_scan: testing l2 1
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x12, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x13, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x14, val=19: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x15, val=13: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x16, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x17, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x19, val=73: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1a, val=08: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1b, val=a9: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1c, val=ff: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1d, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1e, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x21, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=03: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x23, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x24, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x0f, val=07: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x22, ERROR: short packet
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=b3: OK
rfid_asic_rc632.c(371):rc632_transceive: timer = 92
rfid_asic_rc632.c(207):best_prescaler: timeout 920 usec, prescaler = 0, divisor = 6
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2a, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2b, val=06: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x07, ERROR: short packet
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2c, val=c3: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=7f: OK
rfid_reader_openpcd.c(206):openpcd_fifo_write: len=1, data= 26
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=1e: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR sending command
rfid_asic_rc632.c(802):rc632_iso14443a_transceive_sf: error during
rc632_transceive()
rfid_layer2_iso14443a.c(144):iso14443a_anticol: error during transceive_sf: -19
rfid_scan.c(54):rfid_layer2_scan: testing l2 2
rfid_layer2_iso14443b.c(302):iso14443b_init: fsd is 64
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: ERROR sending
command
rfid_layer2_iso14443b.c(310):iso14443b_init: error during reader 14443b init
rfid_scan.c(54):rfid_layer2_scan: testing l2 3
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=4b: ERROR sending
command
rfid_scan.c(54):rfid_layer2_scan: testing l2 4
rfid_scan.c(54):rfid_layer2_scan: testing l2 5
rfid_scan.c(54):rfid_layer2_scan: testing l2 6
rfid_scan.c(54):rfid_layer2_scan: testing l2 7
rfid_scan.c(54):rfid_layer2_scan: testing l2 8
rfid_scan.c(54):rfid_layer2_scan: testing l2 9
rfid_scan.c(54):rfid_layer2_scan: testing l2 10
rfid_scan.c(54):rfid_layer2_scan: testing l2 11
rfid_scan.c(54):rfid_layer2_scan: testing l2 12
rfid_scan.c(54):rfid_layer2_scan: testing l2 13
rfid_scan.c(54):rfid_layer2_scan: testing l2 14
rfid_scan.c(54):rfid_layer2_scan: testing l2 15
.

NON-WORKING SVN HEAD FIRMWARE

lt-librfid-tool - (C) 2006 by Harald Welte
This program is Free Software and has ABSOLUTELY NO WARRANTY

initializing librfid
opening reader handle
No Omnikey Cardman 5121 found
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=10: OK
rfid_asic_rc632.c(158):rc632_power_up: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=10: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x00, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_asic_rc632.c(151):rc632_turn_off_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=58: OK
rfid_asic_rc632.c(144):rc632_turn_on_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, ERROR: short packet
rfid_reader_openpcd.c(500):openpcd_open: returning 0xb7f4fe3c
scanning for RFID token...
rfid_scan.c(54):rfid_layer2_scan: testing l2 0
rfid_scan.c(54):rfid_layer2_scan: testing l2 1
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x12, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x13, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x14, val=19: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x15, val=13: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x16, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x17, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x19, val=73: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1a, val=08: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1b, val=a9: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1c, val=ff: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1d, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1e, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x21, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=03: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x23, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x24, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x0f, val=07: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x22, ERROR: short packet
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=b3: OK
rfid_asic_rc632.c(371):rc632_transceive: timer = 92
rfid_asic_rc632.c(207):best_prescaler: timeout 920 usec, prescaler = 0, divisor = 6
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2a, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2b, val=06: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x07, ERROR: short packet
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2c, val=c3: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=7f: OK
rfid_reader_openpcd.c(206):openpcd_fifo_write: len=1, data= 26
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=1e: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x03, ERROR: short packet
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, ERROR sending command
rfid_asic_rc632.c(802):rc632_iso14443a_transceive_sf: error during
rc632_transceive()
rfid_layer2_iso14443a.c(144):iso14443a_anticol: error during transceive_sf: -19
rfid_scan.c(54):rfid_layer2_scan: testing l2 2
rfid_layer2_iso14443b.c(302):iso14443b_init: fsd is 64
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: ERROR sending
command
rfid_layer2_iso14443b.c(310):iso14443b_init: error during reader 14443b init
rfid_scan.c(54):rfid_layer2_scan: testing l2 3
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=4b: ERROR sending
command
rfid_scan.c(54):rfid_layer2_scan: testing l2 4
rfid_scan.c(54):rfid_layer2_scan: testing l2 5
rfid_scan.c(54):rfid_layer2_scan: testing l2 6
rfid_scan.c(54):rfid_layer2_scan: testing l2 7
rfid_scan.c(54):rfid_layer2_scan: testing l2 8
rfid_scan.c(54):rfid_layer2_scan: testing l2 9
rfid_scan.c(54):rfid_layer2_scan: testing l2 10
rfid_scan.c(54):rfid_layer2_scan: testing l2 11
rfid_scan.c(54):rfid_layer2_scan: testing l2 12
rfid_scan.c(54):rfid_layer2_scan: testing l2 13
rfid_scan.c(54):rfid_layer2_scan: testing l2 14
rfid_scan.c(54):rfid_layer2_scan: testing l2 15

WORKING OTHER DEVICE WHICH I HAVEN'T RESET - The first one wasn't working
(lights flashed etc but no mifare cards detected) so it started down the path of
updating it. I've done the dfu-programmer path and also the SAMBA stuff to
completely reset things - and still no result in terms of getting mifrare cards
read which work fine with the other reader.

Now the same command run on the one which works (which I haven't changed the
firmware) gives:

lt-librfid-tool - (C) 2006 by Harald Welte
This program is Free Software and has ABSOLUTELY NO WARRANTY

initializing librfid
opening reader handle
No Omnikey Cardman 5121 found
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=10: OK
rfid_asic_rc632.c(158):rc632_power_up: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=10: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x00, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_asic_rc632.c(151):rc632_turn_off_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=58: OK
rfid_asic_rc632.c(144):rc632_turn_on_rf: entering
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x11, val=58: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(500):openpcd_open: returning 0xb7f28e3c
scanning for RFID token...
rfid_scan.c(54):rfid_layer2_scan: testing l2 0
rfid_scan.c(54):rfid_layer2_scan: testing l2 1
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x09, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x11, val=5b: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x12, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x13, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x14, val=19: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x15, val=13: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x16, val=3f: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x17, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x19, val=73: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1a, val=08: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1b, val=a9: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1c, val=ff: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1d, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x1e, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x21, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=03: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x23, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x24, val=63: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x0f, val=07: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=00: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x22, val=03: OK
rfid_asic_rc632.c(371):rc632_transceive: timer = 92
rfid_asic_rc632.c(207):best_prescaler: timeout 920 usec, prescaler = 0, divisor = 6
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2a, val=06: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2b, val=06: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x07, val=01: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=21: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2c, val=c3: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=7f: OK
rfid_reader_openpcd.c(206):openpcd_fifo_write: len=1, data= 26
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=1e: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, val=00: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x04, val=02: OK
rfid_reader_openpcd.c(183):openpcd_fifo_read:  ret = 6
len=2 val= 04 00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x0f, val=00: OK
rfid_layer2_iso14443a.c(149):iso14443a_anticol: ATQA: 0x04 0x00
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x09, val=00: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x22, val=03: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x0f, val=00: OK
rfid_asic_rc632.c(371):rc632_transceive: timer = 50
rfid_asic_rc632.c(207):best_prescaler: timeout 500 usec, prescaler = 0, divisor = 5
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2a, val=05: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2b, val=06: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x07, val=1d: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=3d: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2c, val=d4: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=7f: OK
rfid_reader_openpcd.c(206):openpcd_fifo_write: len=2, data= 93 20
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=1e: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, val=00: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x04, val=05: OK
rfid_reader_openpcd.c(183):openpcd_fifo_read:  ret = 9
len=5 val= c4 04 f7 d7 e0: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x0a, val=40: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x22, val=0f: OK
rfid_asic_rc632.c(371):rc632_transceive: timer = 1236
rfid_asic_rc632.c(207):best_prescaler: timeout 12360 usec, prescaler = 0,
divisor = 10
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2a, val=0a: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2b, val=06: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x07, val=1d: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=3d: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x2c, val=a4: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=00: OK
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x07, val=7f: OK
rfid_reader_openpcd.c(206):openpcd_fifo_write: len=7, data= 93 70 c4 04 f7 d7 e0
rfid_reader_openpcd.c(141):openpcd_reg_write: reg=0x01, val=1e: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x01, val=00: OK
rfid_reader_openpcd.c(158):openpcd_reg_read: reg=0x04, val=01: OK
rfid_reader_openpcd.c(183):openpcd_fifo_read:  ret = 5
len=1 val= 08: OK
rfid_layer2_iso14443a.c(252):iso14443a_anticol: UID  c4 04 f7 d7
rfid_layer2_iso14443a.c(260):iso14443a_anticol: we have a T!=CL PICC
rfid_scan.c(91):rfid_protocol_scan: testing proto 0
rfid_scan.c(91):rfid_protocol_scan: testing proto 1
rfid_scan.c(91):rfid_protocol_scan: testing proto 2
rfid_scan.c(91):rfid_protocol_scan: testing proto 3
Layer 2 success (ISO 14443-3 A):  c4 04 f7 d7
Protocol success (Mifare Classic)
Size: 1024 bytes

-------------- next part --------------
A non-text attachment was scrubbed...
Name: PGP.sig
Type: application/pgp-signature
Size: 487 bytes
Desc: not available
Url : http://lists.openpcd.org/pipermail/openpcd-devel/attachments/20080123/e2b5d108/PGP-0001.pgp